View H5D-250-E_350413.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

H5D
Differential Heavy Duty Optical Shaft Encoder
Features:
O O O O O O O O O O O O
Description:
The H5D differential optical incremental encoder is fully assembled with a shaft, two 1/4" ID by 1/2" OD heavy duty ball bearings and a mounting plate. This design tolerates increased radial and axial loads. This design also allows for an optional rear shaft extension. The mounting plate comes with 2 mounting holes for screws #6 or smaller. The mating connector has 10 pins, is polarized and latches into the encoder. Depressing the latch tab allows the connector to be unplugged. Mating connector assemblies are available from US Digital stock as shown on the Cables & Connectors data sheet. Custom cables are also readily available. The H5D has an internal differential line driver (26C31) that can source and sink 20mA at TTL levels. The cable that connects to this encoder should have 3 twisted pairs plus power and ground. Group each pair of differential signals. The recommended receiver is industry standard 26C32. Maximum noise immunity is achieved when the differential receiver has a 110 Ohm resistor in series with a .0047mf capacitor placed across each differential pair. The capacitor simply conserves power; otherwise power consumption would increase by 45mA per pair, or 140 mA for 3 pairs. Electrical Specifications: B leads A in a clockwise shaft rotation, and A leads B in counterclockwise shaft rotation viewed from the shaft side of the H5D. For complete details see the HEDS data sheet.
Small size Low cost Optional Agilent compatible pin-out Positive finger-latching polarized connector 2-channel quadrature, TTL squarewave outputs 3rd channel index option Differential line driver outputs Tracks from 0 to 100,000 cycles/sec Heavy duty ball bearings track up to 10,000 RPM -40 to +100C operating temperature Single +5VDC supply US Digital warrants its products against defects and workmanship for two years. See complete warranty for details.
Pin Descriptions:
Pin 1 2 3 4 5 6 7 8 9 10 Standard Ground Ground IndexIndex+ A- channel A+ channel +5VDC power +5VDC power B- channel B+ channel
Mechanical Specifications:
Agilent (L-option) No connection +5VDC power Ground No connection A- channel A+ channel B- channel B+ channel IndexIndex+
Mechanical Notes:
Shaft speed Acceleration Shaft torque Shaft loading Bearing life Weight Shaft runout Moment of inertia Vibration
10,000 RPM max. continuous 250,000 rad/sec 2 0.05 in. oz. max. 2 lbs. max. (90/P)3 - life in millions of revs. 1.83 oz. .0006 T.I.R. max. .0001 oz. in. s2 20 g. 5 to 2KHz
Compatible Cables & Connectors:
10-pin Finger-latching: CON-FC10 Connector CA-3619 Connector on both ends of a 6' shielded round cable CA-3807 Same as CA-3619, but for L-option only CA-4217 Connector on one end with a 6' shielded round cable Note: See Cables & Connectors data sheet for more information. Min. 4.5 2.4 Typ. 5 65 25 65 3.4 0.4 Max. 5.5 95 50 95 0.8 Units Volts mA mA mA Volts Volts Notes no load no load no load @ -20mA @ 20mA
Electrical Notes:
Specification Supply Current consumption index non-index <1000 CPR non-index =>1000 CPR Output voltage sourcing to +5 sinking to ground
Ordering Information:
H5D CPR: 50 96 100 110* 120* 192* 200 250 256 360 400 500 540* 1000* 1016* 1024* Options**: I = Index (3rd channel). L = Agilent compatible pin-out. E = Rear shaft extension. Notes: * Index option not available. ** Specify options in order shown.
TM
H5D Price: $69 / 1 $66 / 10 $62 / 50 $59 / 100 $57 / 500 $53 / 1000
Cost Modifiers: O Add $9 for index and/or resolutions =>1000 CPR. O Add $2 for E-option.
US
Technical Data, Rev. 08.07.01, August 2001 All information subject to change without notice.
Corporation
Digital
phone: 360.260.2468 l sales: 800.736.0194 l fax: 360.260.2469 email: sales@usdigital.com l website: www.usdigital.com 11100 ne 34th circle l vancouver, washington 98682 USA
page 1

▲Up To Search▲

Price & Availability of H5D-250-E

	To Download H5D-250-E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .